PIC16F785-I/SS【PDF 51/206 页】IC PIC MCU FLASH 2KX14 20SSOP

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3887

47页 48页 49页 50页 [51页]52页 53页 54页 55页

144

8272E–AVR–04/2013

ATmega164A/PA/324A/PA/644A/PA/1284/P

17.2.1

Registers

The Timer/Counter (TCNT2) and Output Compare Register (OCR2A and OCR2B) are 8-bit reg-

isters. Interrupt request (abbreviated to Int.Req.) signals are all visible in the Timer Interrupt Flag

(TIMSK2). TIFR2 and TIMSK2 are not shown in the figure.

The Timer/Counter can be clocked internally, via the prescaler, or asynchronously clocked from

the TOSC1/2 pins, as detailed later in this section. The asynchronous operation is controlled by

the Asynchronous Status Register (ASSR). The Clock Select logic block controls which clock

source the Timer/Counter uses to increment (or decrement) its value. The Timer/Counter is inac-

tive when no clock source is selected. The output from the Clock Select logic is referred to as the

timer clock (clk

T2).

The double buffered Output Compare Register (OCR2A and OCR2B) are compared with the

Timer/Counter value at all times. The result of the compare can be used by the Waveform Gen-

erator to generate a PWM or variable frequency output on the Output Compare pins (OC2A and

OC2B). See “Output Compare unit” on page 145 for details. The compare match event will also

set the Compare Flag (OCF2A or OCF2B) which can be used to generate an Output Compare

interrupt request.

17.2.2

Definitions

Many register and bit references in this document are written in general form. A lower case “n”

replaces the Timer/Counter number, in this case 2. However, when using the register or bit

defines in a program, the precise form must be used, that is, TCNT2 for accessing

Timer/Counter2 counter value and so on.

The definitions in Table 17-1 are also used extensively throughout the section.

17.3

Timer/Counter clock sources

The Timer/Counter can be clocked by an internal synchronous or an external asynchronous

clock source. The clock source clk

T2 is by default equal to the MCU clock, clkI/O. When the AS2

bit in the ASSR Register is written to logic one, the clock source is taken from the Timer/Counter

Oscillator connected to TOSC1 and TOSC2. For details on asynchronous operation, see ”ASSR

– Asynchronous Status Register” on page 161. For details on clock sources and prescaler, see

”Timer/Counter Prescaler” on page 156.

Table 17-1.

Definitions.

BOTTOM

The counter reaches the BOTTOM when it becomes zero (0x00).

MAX

The counter reaches its MAXimum when it becomes 0xFF (decimal 255).

TOP

The counter reaches the TOP when it becomes equal to the highest value in the

count sequence. The TOP value can be assigned to be the fixed value 0xFF

(MAX) or the value stored in the OCR2A Register. The assignment is depen-

dent on the mode of operation.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式